Q re torque box positioning
Moderator: Moderators
Q re torque box positioning
Well being an idiot I didn’t take pics of the inside of the torque box positioning. To be fair their wasn’t a lot of the old box there and they had screwed new floor over the old floor which was pretty ugly.
I have patched the sections of the inside kick panel where the old torque box and type board attached finally and getting ready to install torque box.
I have the 2pce Dii torque box and the lower section sits in properly, however I cannot recall whether the top plate lip goes under or over the frame rail/floor support section. The 2 sections of the box don’t mate up well when it is sitting on top of the rail yet I have been looking on the net and it seems most have the top piece sitting on top of the frame rail?
Any help appreciated.
Cheers
Craig
I have patched the sections of the inside kick panel where the old torque box and type board attached finally and getting ready to install torque box.
I have the 2pce Dii torque box and the lower section sits in properly, however I cannot recall whether the top plate lip goes under or over the frame rail/floor support section. The 2 sections of the box don’t mate up well when it is sitting on top of the rail yet I have been looking on the net and it seems most have the top piece sitting on top of the frame rail?
Any help appreciated.
Cheers
Craig
Cheers
Craig
Craig
Re: Q re torque box positioning
Goes under the lip of the rail. If you had it assembled & jacked it in place, it would be under. That is how the factory did it.
The torque boxes were an afterthought in all the body shapes (at first only convertibles had them) so the firewall/ foot Wells were designed to fit the rails if it had torque boxes or not. So they made them fit by designing them to be under, saving a redesign of the firewall/ foot well.
The torque boxes were an afterthought in all the body shapes (at first only convertibles had them) so the firewall/ foot Wells were designed to fit the rails if it had torque boxes or not. So they made them fit by designing them to be under, saving a redesign of the firewall/ foot well.
Kerry
To our wives and sweethearts. May they never meet
To our wives and sweethearts. May they never meet
Re: Q re torque box positioning
Thanks Kerry. Much appreciated - feel free to come up and show me how it’s done - I’ll make pizza ?
Cheers
Craig
Craig
Re: Q re torque box positioning
6 trips up there in the last year, maybe no more for a while.
Kerry
To our wives and sweethearts. May they never meet
To our wives and sweethearts. May they never meet
Re: Q re torque box positioning
BTW, I hate pizza, bloody flavoured card boardChux wrote:Thanks Kerry. Much appreciated - feel free to come up and show me how it’s done - I’ll make pizza ?
Kerry
To our wives and sweethearts. May they never meet
To our wives and sweethearts. May they never meet
Re: Q re torque box positioning
Woodfired oven....ribs or a roast?ozbilt wrote:BTW, I hate pizza, bloody flavoured card boardChux wrote:Thanks Kerry. Much appreciated - feel free to come up and show me how it’s done - I’ll make pizza ?
Cheers
Craig
Craig
Re: Q re torque box positioning
We've only got lots of great wine down here in SA for you Kerry.
Re: Q re torque box positioning
Don't drink either (ok tea I do drink). However, Mrsozbilt does not mind a glass (or two) of wine ........Dwayne wrote:We've only got lots of great wine down here in SA for you Kerry.
Kerry
To our wives and sweethearts. May they never meet
To our wives and sweethearts. May they never meet
Re: Q re torque box positioning
Keeps those hands steady....ozbilt wrote:Don't drink either (ok tea I do drink). However, Mrsozbilt does not mind a glass (or two) of wine ........Dwayne wrote:We've only got lots of great wine down here in SA for you Kerry.
Cheers
Craig
Craig
Re: Q re torque box positioning
Always welcome down here.ozbilt wrote:Don't drink either (ok tea I do drink). However, Mrsozbilt does not mind a glass (or two) of wine ........Dwayne wrote:We've only got lots of great wine down here in SA for you Kerry.
Re: Q re torque box positioning
There is plenty of tea for you over in the west Kerry..... cause we all drink beer and wine so feel free to come and build FnL. I boil a pretty mean kettle.
Last edited by nassi on Sun May 27, 2018 9:46 pm, edited 1 time in total.